Forum Discussion

DRISCOLL0424's avatar
DRISCOLL0424
Network Novice
Hace 7 meses

T-mobile -- White mesh -- can't get it to pair -- have tried everything!

No matter what I try I cannot get the white mesh disks to pair.

I have spent hours on the phone with support...I have reset factory reset my gateway, the mesh several times...and all it does is blink white.  They have sent me knew ones… same result.  I don't know what else to do that this point.  Does anyone know how to fix?

¡Gracias!

  • Troubleshooting suggestions - start upstream and work your way down.

    Does the gateway work by itself?  (Can any of your devices connect to it?)

    If it doesn’t, that’s the problem. 

    If it does, have you tried pairing the mesh units very close to the gateway?  After they pair, move them.  If they still won't pair, you could try something different, such as connecting your old Wi-Fi router to the gateway with an Ethernet cable.  See how far that signal reaches, and if necessary, add extenders to make your own "mesh" network.

  • JD1's avatar
    JD1
    Roaming Rookie
    Jstevcam wrote:

    This is my mesh devices behavior and the issue, so how can I get support to send firmware update?  Don't have hours to spend on phone with support.  Who does?

    I just called tmobile customer support who transferred me to the home internet technician. We went over everything and then he said he was going to try to push a firmware update to the modem not the mesh.  I honestly do not know if the one helping me had more access than your average tech personal to overide something or see more info into my device. (i.e. a higher up ). But i do remembet being put on wait a couple times so he could talk to a higher up and see what to do next. And then eventually he was able to push it. So it could be that is something a higher up can do but not a regular tech? 

    Unfortunately i do not know the firmware option. 

  • Tried it all. Powered off, factory reset mesh, ethernet, proximity

    and more, at least 3x each.  After a few hours and some tech help finally figured out how to fix 2 problems actually. 

    I was about to hang up with tech support when I recalled how my daughter's tablet would not connect to the main router even though it worked fine for everything else.  I learned it was not 5g compatible.  I asked the tech to help me set up. 2.4ghz line for that.  

    Here is the fix that worked for both.

    Using the tLife app, I created a second network.  To do this I selected the home button on Tlife. Then on the overview page I selected +add network, then give your new wifi network a name (I used the same name but added 24 to it) I used the same password, then change the frequency band to 2.4ghz, then change the wpa version to wpa/wpa2, keep the encryption mode the same and hit save.  The moment I did this, it says it takes 90 seconds to work, but my mesh extender finally stopped blinking white, turned red, and then green.

     

    Now everything works.  The extender, the old tablets.  We are happy.  The whole thing takes 5 minutes to try.  You spent longer reading this probably.   Good luck.

  • dmengelbert wrote:

    Went ahead and called. Tech says his diagnostic shows I have the lastest firmware update. Says I need a new mesh. This was a new mesh. So frustrated at this point and not sure I want to continue with the service if this continues to be an issue. Trying to trade really bad ISP and don't want to go to one that I have to call tech support every other day.

    Was right there with you.  Try my idea.

  • Thanks, Tiger_Mentor19. It didn't work. I'm going to try a factory reset of both gateway and mesh then calling support one more time. If that doesn't work, it all goes back and I live with crappy internet that at least requires less support. Sometimes the devil you know is better than the one you don't.

  • I have one mesh basically sitting directly above gateway on second floor. It seems to at least connect to gateway, but seems close. The second tmobile mesh, was hoping to put in attached garage, but only seems to get a connection when its in the same room as the gateway which seems worthless and not the 2000sg feet mesh i was looking for. Any thoughts? I wanted to get 3-4000 sq feet using the two tmobile mesh. Gracias

  • How do i know if i need a firmware update for a gateway or mesh? Gracias

  • Herptiles wrote:

    How do i know if i need a firmware update for a gateway or mesh? Gracias

    You need to call their customer service. They'll walk you through finding your firmware number and they'll have the current number.

    I had to call customer service a few times the day I set things up and all but one were great. The 'one' that wasn't so great just seemed new. She just wanted to send me a new mesh. I knew that wasn't the solution. Setting up tech isn't a new thing for me. She really didn't want me to end the call and go to someone else. She even called me back and wanted to get the new mesh mailed out to me. I told her not to call me back again. I'd prefer someone else.

    The next young man was incredible! There were some issues he hadn't encountered on his end of things, but he plowed through, found the solutions and got the update I needed. It's worked great ever since.